Analysis of 3 Phase Induction Motor Speed Control with Direct Torque Control (DTC) Method Based on PID Control

Authors

  • Mokh. Suseno Aji Sari Department of Electrical Engineering, Faculty of Engineering, Universitas Brawijaya , Jurusan Teknik Elektro Fakultas Teknik Universitas Brawijaya
  • Hadi Suyono Department of Electrical Engineering, Faculty of Engineering, Brawijaya University , Jurusan Teknik Elektro, Fakultas Teknik, Universitas Brawijaya
  • Abraham Lomi Department of Electrical Engineering, Faculty of Engineering, Brawijaya University , Jurusan Teknik Elektro, Fakultas Teknik, Universitas Brawijaya

DOI:

https://doi.org/10.33019/jurnalecotipe.v7i2.1476

Keywords:

Direct Torque Control, 3-Phase Induction Motor, PID Control, Tuning

Abstract

This research was conducted to regulate the three phase induction motor speed regulation system. Changes in load on the motor affect the motor speed response so it does not match the set point speed. This study uses the Direct Torque Control (DTC) method in regulating the speed of an induction motor. The DTC method is a vector control method that is directly assigned to the inverter. DTC method in controlling speed based on Proportional Integral Differential (PID) control. Determination of PID tunning using two methods, namely, ziegler-nichols and cohen-coon method. The ziegler-nichols method have overshoot speeds starting at 0.8% of the setpoint, whereas using the cohen coon method there is no overshoot and the speed at stable conditions matches the setpoint.

Downloads

Download data is not yet available.

References

Abu, Haitham. Atif Iqbal and Jaroslaw Guzinki (2012). High-Performance Control Of AC Drives With Matlab/Simulink Models. Thomson Digital, Nodia: India.

Alnasir, ZA. & Almarhoon AH. (2012). Design of Direct Torque Controller of Induction Motor (DTC). International Journal of Engineering and Technology (IJET) No : 0975-4024

Astrom, Karl Johan, (1995). PID Controller. Printed in the United States of America. ISBN : 1-55617-516-7

Buja. G. S and Kazmierkowski. M. P,(2004) "DTC of pwm inverter-fed AC motors - A Survey", IEEE Trans. on Ind. Elec., volume 54, no. 5, , pp. 744 – 757

Chapman, Stephen J. (2002). Electric Machinery And Power System Fundamentals, New York: Mc Graw-Hill.

Dong ming, Tang Yong-qi dkk. (2013). Study of an Improve Fuzzy Direct Torque Control Of Induction Motor. Telkomnika.

K.Ogata. (2010) Modern Control Engineering, Fifth ed. New Jersey, Prentice Hall,.

Parekh, Rakesh. (2005). VF Control of 3-Phase Induction Motor Using Space Vector Modulation. Microchip Technology Inc.

Rameli. (2007). Diktat Kuliah Kontrol Electric Drive. ITS: Surabaya.

Vahedpour M., Abolfazl R.N. (2015). Comparison between performance of Conventional, Fuzzy and Fractional Order PID Controller in Practical Speed Control Of Induction Motor. International Conference on Knowledge-Based Engineering and Innovation (KBEI). Iran.

Published

30.10.2020

How to Cite

[1]
M. S. A. Sari, H. Suyono, and A. Lomi, “Analysis of 3 Phase Induction Motor Speed Control with Direct Torque Control (DTC) Method Based on PID Control”, JurnalEcotipe, vol. 7, no. 2, pp. 70–77, Oct. 2020, doi: 10.33019/jurnalecotipe.v7i2.1476.

Most read articles by the same author(s)